Отправка в тот же день для всех заказов, размещенных до 14:00 по всей Европе с использованием DPD.
Нет товаров
Цены указаны с учетом НДС
Товар добавлен в корзину
Товаров в корзине: 0. Сейчас в корзине 1 товар.
Биты Н.З.
Откройте для себя наши 82 ссылок в этой категории : Биты Н.З.- 1
- 2
Diamond routing bits Z1+1
DIAM01In highly wear-resistant special steel. 2 PD cuts. 1 WH cut for drilling.
From 113,75 €-
Universal profile cutter for cnc machines
CMT663.301.11For universal profiling of solid wood on CNC router machines. For cutting width 40mm and 50mm ( serie 690). Profile knives may only be ordered and used in pairs. For router machines with mechanical feed.
From 237,66 € -
Solid surface and fiberglass bit
CMT151-1For drilling, sizing and jointing fiberglass, phenolic and solid surfaces. Can be used on machining centers, point to point machines, CNC routers and and held routers equipped with chucks or adaptors.
From 54,21 € -
Solid up and downcut spiral bits - Long Life
CMT190.41For precision edging, sectioning and crowning of solid wood or timber, laminates and plastic materials with surprising efficiency and very high feed rate. to be used on chucks or adapters for CNC machining centers, CNC routers and pantographs. Clamp the workpieces on the work surface.
From 190,26 € -
Diamond sizers for asymmetical edgebander
PCDIA-02For facing and sizing particleboard and MDF panels on double sizer or edgebander.
From 712,38 € -
Planing cutter with Xtreme reversible knives
CMT663.5New milling cutter for CNC pantographs, ideal for planing and for quickly removing material from large surfaces, guaranteeing a good finish.For use on soft and hard wood, chipboard and MDF.Economically attractive solution thanks to the reversible knives.
From 228,06 € -
Solid carbide upcut spiral bits
CMT198Used for cutting, copying, panel sizing and any routing applications on solid wood, wood composites, plastic materials and laminates. Use a high feed speed on well-clamped workpieces. Can be used on machining centres, point to point machines, CNC routers and hand-held routers equipped with chucks or adaptors.
From 39,85 € -
-
-
Solid surface and fiberglass bit
CMT151-2For drilling, sizing and jointing fiberglass, phenolic and solid surfaces. Can be used on machining centers, point to point machines, CNC routers and and held routers equipped with chucks or adaptors.
From 54,21 € -
Z2 ONE WEEK facing and profiling cutter head
PM049-01- Steel cutter head- Right hand rotation- MEC / mechanical feed
From 281,93 € -
Diamond sizers for symmetical edgebander
PCDIA-03For facing and sizing particleboard and MDF panels on double sizer or edgebander.
From 801,41 € -
5%co HS spiral bits for aluminium positive single flute
CMT188These tools feature single flute design allowing both efficient and effective carving on all types of aluminium. The final result is a higher flexibility than traditional bits, enhanced productivity and high quality finishing.
From 15,33 € -
-
Solid carbide Upcut 2D/3D Carving Tapered Ball Noise...
CMT152Specially designed for 2D and 3D CNC profiling and carving in plastic, aluminum and wood for several uses like: - A perfect bit for 3D carving - Precision 2D and 3D large scale carving - Great for deep profiling - Dimensional signage - 3D millwork - 2D and 3D contouring, profiling, modeling, and pattern making for cabinetry, sign making, furniture making...
From 55,15 € -
Z2 diamond router bits for compact type materials
DIAM11Made of highly wear-resistant special steel.2 PD cutting edges. Sharpenable 3-4 times.For drilling and edge laminate and plastic materials. To be used on chucks or adapters for machining center.
From 290,11 € -
5%co HS spiral bits for aluminium single flute for high...
CMT189These tools feature single flute design allowing both efficient and effective carving on all types of aluminium. The final result? Higher flexibility than traditional bits, enhanced productivity and high quality finishing.
From 24,03 € -
Diamond routing bits Z2+2
DIAM02In highly wear-resistant special steel. 2+2 mitre cuts on 4 helixes.
From 385,15 € -
Solid carbide upcut spiral bits for aluminum and PVC
CMT186Used for ripping, template routing and panel sizing on plastic materials and aluminum at high feed speed.Can be used on machining centers, point to point machines, CNC routers and hand held routers equipped with chucks or adaptors.
From 44,21 € -
Carbide spiral bits for aluminium single flute
MECH02HWM. 1 upcut spiral cutting edge [Z1].
From 96,42 € -
-
Z2 diamond router bits with 40° axial cutting edges.
DIAM12Made of highly wear-resistant special steel.2 PD cutting edges. 1 PD cutting edge to be cut.For high speed work. Excellent finish on panels and front veneers.To drill and edge laminates and MDF. To be used on chucks or adapters for machining center.
From 701,44 € -
Diamond routing bits Z3
DIAM04In highly wear-resistant special steel. 3 PD cuts. 1 PD cut for drilling.
From 698,58 € -
Cutter heads for making expandables grooves on CNC
FRAI105For making expandable grooves on CN.
From 725,04 € -
Carbide spiral bits for aluminium single flute
MECH03HWM. 1 upcut spiral cutting edge [Z1].
From 150,20 € -
Solid carbide upcut spiral bits chip-breaker for 60°...
CMT195.143-163Used for cutting, copying, panel sizing and any routing applications on solid wood, wood composites, plastic materials and laminates. Use a high feed speed on well-clamped workpieces. Can be used on machining centres, point to point machines, CNC routers and hand-held routers equipped with chucks or adaptors.
From 203,22 € -
Diamond milling bits Z2. TRESPA - COMPACT
DIAM06In highly wear-resistant special steel. 2 PD cuts. TRESPA - COMPACT
From 806,95 € -
Solid carbide upcut spiral bits for locksets
CMT195-02Used for cutting, copying, panel sizing and any routing applications on solid wood, wood composites, plastic materials and laminates. Use a high feed speed on well-clamped workpieces. Can be used on machining centres, point to point machines, CNC routers and hand-held routers equipped with chucks or adaptors.
From 216,51 € -
Adjustable grooving cutter head with knives Z2 + 2, V2 + 2
ME110WS-01- Grooving cutting head for solid wood and panels of all kinds (coated or non-coated)- Steel body with reversible carbide knives on 4 cutting edges- Two-piece, adjusted by spacers- Recommended for routers and CNC machines - MEC / mechanical feed
From 503,45 € -
Upcut spiral bits with chipbreaker for glue-laminated...
CMT195-03Used for cutting, copying, and routing on glue-laminated wooden beams. To be inserted on Hundegger® machines.
From 781,16 € -
Flush trim and surfacing bits with Z3 knives
PS122WS-01- Bit with reversible 4-sided carbide knives for fast rebating, flush trimming and surfacing large surface areas- Suitable for soft and hardwood and all kinds of panels- Recommended for routers and CNC machines- MEC / mechanical feed
From 374,72 € -
NESTING diamond routing bits 3 high
DIAM13Made of highly wear-resistant special steel.3 PD cutting edges. 1 PD cutting edge to be cut.Sharpenable 4-6 times. Specially designed for nesting.Excellent finish on panels and front veneers.To drill and edge laminates and MDF. To be used on chucks or adapters for machining center.
From 445,60 € -
Solid carbide upcut with spiral bits chip-breaker for 60°...
CMT191.143-163Used for cutting, copying, panel sizing and any routing applications on solid wood, wood composites, plastic materials and laminates. Use a high feed speed on well-clamped workpieces. Can be used on machining centres, point to point machines, CNC routers and hand-held routers equipped with chucks or adaptors.
From 145,52 € -
Spoilboard surfacing router cutters with insert knives
CMT663New router bit for CNC router ideal for fast removal of material over a large surface area leaving an improved finish at the bottom of the cut. Used on soft and hardwood, particle board and MDF. The cutter uses 4-sided inserts. Cost effective solution compared to brazed router bits and solid carbide spiral bits.
From 231,55 € -
-
-
Solid carbide upcut spiral bits with chipbreaker
CMT197A special super-micrograin carbide formulation was created to produce and hold a keen cutting edge. The new low-angle spiral is designed specifically to shear wood cleanly and provide efficient chip ejection. The tools run cooler and the edges last longer.Used for cutting, copying, panel sizing and any routing applications on solid wood, wood composites,...
From 129,18 € -
-
Solid carbide upcut spiral bits with chipbreaker
CMT195-01Used for cutting, copying, panel sizing and any routing applications on solid wood, wood composites, plastic materials and laminates. Use a high feed speed on well-clamped workpieces. Can be used on machining centres, point to point machines, CNC routers and hand-held routers equipped with chucks or adaptors.
From 57,75 € -
Z2 diamond drill bits - Blind holes
DIAM07To make blind holes on multiple spindle drills.
From 167,28 € -
Joining cutter head for woodwork
EU8020-01- For glue joints of edging- Cutters with PRECIS-CUT carbide knives- Cutter head mounted on CNC arbor
From 1 272,71 € -
Solid carbide upcut spiral bits
CMT191Used for cutting, copying, panel sizing and any routing applications on solid wood, wood composites, plastic materials and laminates. Use a high feed speed on well-clamped workpieces. Can be used on machining centres, point to point machines, CNC routers and hand-held routers equipped with chucks or adaptors.
From 30,19 € -
Z2 diamond drill bits - Through holes
DIAM08To make through holes on multiple spindle drills.
From 255,10 € -
Z2 glue joint tongue and groove cutter head
PA020WS-01To produce glue joints in soft and hardwood. Non-reversible carbide knives with positioning stop for quick and precise positioning + an eccentric ring for lateral adjustment of the knives for the glue joint, depending on the species of wood processed.
From 753,60 € -
Solid carbide downcut spiral bits with chipbreaker
CMT196Used for cutting, copying, panel sizing and any routing applications on solid wood, wood composites, plastic materials and laminates. Use a high feed speed on well-clamped workpieces. Can be used on machining centres, point to point machines, CNC routers and hand-held routers equipped with chucks or adaptors.
From 52,34 € -
Diamond self feed drill bits
DIAM09To make hinges with multiple spindle drills.Can be sharpened 6-8 times.
From 240,65 € -
Solid carbide up & downcut spiral bits
CMT190Used for cutting, copying, panel sizing and any routing applications on solid wood, wood composites, plastic materials and laminates. Use a high feed speed on well-clamped workpieces. Can be used on machining centres, point to point machines, CNC routers and hand-held routers equipped with chucks or adaptors.
From 62,17 € -
Diamond hinge boring bits
CMT317-369Ideal for hinges. Use on boring machines equipped with adaptors or chucks. Use for drilling accurate and clean-cut blind holes in wood composites, plastic and laminated materials. Boring performance 20 times longer than HW materials.
From 521,47 € -
Sizing roughing cutter head Z2 + 2
PC505WS-01- Roughing cutter head with HW knives to size soft and hardwood as well as coated or non-coated panels- Reversible knives with 4 cutting edges, spread over 4 spirals for optimum chip removal and flow- Suitable for routers and CNC machines- MEC / mechanical feed
From 305,89 € -
-
Sizing and rebate cutter head Z2 + 2
PC808WS-01- Cutter head to straighten, size and rebate solid wood and various panels- Particularly suitable for curved woodwork or chair legs- 2+2 alternating mitre cuts with 4-sided reversible carbide knives, helically mounted on 4 divisions + 2 spurs in the lower part- Optimised helix angle and clean cut for high feed rates- To be mounted on cutter arbor Ø30 x...
From 527,40 € -
Solid carbide upcut spiral bits
CMT193Used for cutting, copying, panel sizing and any routing applications on solid wood, wood composites, plastic materials and laminates. Use a high feed speed on well-clamped workpieces. Can be used on machining centres, point to point machines, CNC routers and hand-held routers equipped with chucks or adaptors.
From 42,63 € -
-
Folding and chamfer bits with Z1 knives
PA030WS-01- To produce chamfers, decorative grooves and mitre fold grooves in all kinds of wood and panels- Cutter head with reversible carbide knives with side stop for quick and precise positioning- MEC / mechanical feed
From 340,87 € -
Solid carbide spiral bits downcut
CMT194Used for cutting, copying, panel sizing and any routing applications on solid wood, wood composites, plastic materials and laminates. Use a high feed speed on well-clamped workpieces. Can be used on machining centres, point to point machines, CNC routers and hand-held routers equipped with chucks or adaptors.
From 90,11 € -
V-groove - Folding - Signmaking CNC Router Cutter
CMT663.101.11This innovative CNC router bit offers you an endless range of possibilities for V-Groove, miter folds, signmaking, lettering and chamfer edges. The tool mounts a high grade HWM reversible knife ideal for general purpose, chipboard and plywood, but a higher quality is available for laminated and MDF material.
From 204,03 € -
-
Solid carbide downcut spiral bits
CMT192Used for cutting, copying, panel sizing and any routing applications on solid wood, wood composites, plastic materials and laminates. Use a high feed speed on well-clamped workpieces. Can be used on machining centres, point to point machines, CNC routers and hand-held routers equipped with chucks or adaptors.
From 37,16 € -
Diamond router cutters with shear angle
CMT142-1To be used on all CNC routers for jointing, rabbeting, grooving, copying and dividing cuts of raw material, melamine and laminates, MDF, HPL and veneered panels.
From 347,83 € -
Spiral bit with insert knives and chipbreaker for locksets
CMT662The 95mm length is achieved in 4-5 passes.
From 841,27 €
- 1
- 2
Filter by:
Last Posts
-
The Importance of a Well-Sharpened Knife in the Kitchen
Discover how to sharpen your kitchen knives optimally with a sharpening machine.
-
Японские пилы Takagi Shark Saw: Союз традиций и технологий для идеальных резов
Японские пилы Takagi, особенно серия Shark Saw, известны своей эффективностью и точностью.
-
Knife sharpening angle adjuster KS-123 Tormek
Set the perfect sharpening...
-
-
